Husqvarna Nuda 900 Urban Racer Project "Pure Addiction From Fast Bike"

HUSQVARNA NUDA 900

URBAN RACER PROJECT BUILD BIKE

BUILD FINISHED AT END OF AUGUST THIS YEAR AND THE BIKE WAS REG ON A 63 PLATE

AS NEW BIKE BUT WITH A FEW CHANGES

HUSQVARNA INTENDED BUILDING 3 TYPES OF NUDA MODELS

THE FIRST WAS A GENERAL CROSS OVER TYPE OF BIKE

THE SECOND WAS A TOURER TYPE OF BIKE WITH TWO UP CAPABILITY AND THE FACILITY TO CARRY LUGGAGE

THE THIRD TYPE NEVER GOT TO BE PRODUCED AS HUSQVARNA GOT SOLD TO KTM THIS WAS THE PROJECT WE SET OUT ON FINISHING

THE NUDA HYPER-MOTARD

AS YOU CAN SEE FROM THE PHOTOS THE BIKES A BIT DIFFERENT TO THE STD BIKE YOU WOULD SEE IN THE SHOWROOM OF YOUR LOCAL DEALER

THE BIKE WAS BUILT FOR A LOCAL HUSQVARNA DEALER WITH THE INTENTION OFF SELLING THIS TYPE OF BUILD INTO THE USA AND UK

WHEN KTM TOOK OVER THE REINS OF HUSQVARNA UK A LOT OF DEALERS WERE GIVEN AN OPTION TO STOP ON AS KTM / HUSKY DEALERS OR LEAVE THE NETWORK

THE DEALER WHO I BUILT THIS BIKE FOR DECIDED TO PULL OUT OF MOTORCYCLES ALL TOGETHER AND FINISHED WITH KTM.

THIS WASENT A PROBLEM FOR ME AS THE BIKE WAS PURCHASED BY ME AT THE VERY START OF THE BUILD. I JUST LOVED IT AND COULD SEE THE POTENTIAL IN IT.

IT ALSO ATTRACTED THE ATTENTION OF THE ART EDITOR OF FAST BIKE MAGAZINE AND INVITED ME AND THE BIKE FOR A PHOTO SHOOT

FOR THE CENTRE FOLD PULL OUT OF NOVEMBERS EDITION OF FAST BIKE:

www.fastbikesmag.com/2013/10/11/fast-bikes-magazine-november-2013-is-out-now/

THE BIKE

2012 MODEL NON ABS REG ON A 63 PLATE £5800.00

LESS THAN 200 MILES FROM NEW

RED POWDER COATED CHASSIS AND SUB FRAME £150.00

3M CARBON WRAP ON ALL BODYWORK £150.00

NITRON REMOTE 3 WAY SHOCK WITH REMOTE PRELOAD AND REMOTE RESEVIOR £700.00

MAZZ SMR FORK WITH TOP AND BOTTOM YOKES £600.00

BREMBO MONOBLOCK CALIPER £250.00

ISR FULL FLOATING AND DAMPED FRONT DISC £300.00

ALPINA CARBON (RED & BLACK) SPOKED RIMS FRONT AND REAR £1200.00

BILLET ALIMINIUM CONVERSION WITH REAR UNDER SLUNG BRAKE CALIPER AND PADDOCK MOUNTS (CNC DESIGN TIME AND BUILD COST) £1200.00

OPEN AIR BOX CONVERSION £150.00

ARROWS HEADERS MATED TO A CONVERTED UNDER ENGINE EXHAUST CONVERSION £250.00 headers £300.00 can conversion

POWER COMMANDER PCV & AUTO-TUNE (TWIN LAMBA SAMPLING) £550.00

CARBON FIBRE BELLY PAN £320.00

CARBON FRONT FENDER / REDESIGNED LOOK £130.00

CARBON FIBRE EXHAUST CAN END CAP

BILLET ALI FUEL RAIL (CNC DESIGN TIME AND BUILD COST) CONVERSION £150.00

BILLET LEVERS (CLUTCH AND BRAKE) £150.00

520 CHAIN / GEAR CONVERSION £200.00

FOOTPEG CONVERSION £80.00

R&G ENGINE CASE PROTECTORS (BOTH SIDES) R&G BAR WEIGHT ENDS £200.00

ULTRABAT (LITHIUM WEIGHT BATTERY) £200.00

MADE GOOD FIGURES ON THE DYNO AT JT'S PRINT OUT AVAILABLE

JUST PUT A BRAND NEW SC2 ON THE REAR (£130.00) SO READY FOR ACTION.

SO THAT'S £5800.00 FOR THE BIKE AND £7200.00 ON THE BUILD (AND THAT'S NOT INCLUDING THE LABOUR)

TOTAL BUY AND BUILD COST OF OVER £13000.00

SO PLEASE NOTE I WILL NOT BE GIVING THE BIKE AWAY FOR PEANUTS BUT I'L HAVE A DEAL WITH YA.

AS ALWAYS I RESERVE THE RIGHT TO REMOVE THE ABOVE BIKE AS ADVERTISED ELSEWHERE.